Spray Foam Removal near me in Telford
Local spray foam removal in Telford Shropshire, done clean and mortgage-ready
Spray Foam Removal near me in Telford means cutting out failed polyurethane foam from lofts, rafters and cavity walls, then leaving your timber dry and your paperwork mortgage-ready. We handle homes and commercial units across Telford, Shropshire. If a lender has flagged spray foam insulation damage, or you have spotted spray foam shrinkage and loft condensation, we can survey within 48 hours and give you a fixed price before any work starts.
What Spray Foam Removal near me in Telford involves
Spray Foam Removal near me in Telford is the controlled cutting, extraction and disposal of spray foam insulation from roof voids, lofts, rafters and cavity walls. We identify whether you have open cell foam or closed cell foam, because the two behave differently: open cell foam crumbles and traps moisture, while closed cell foam sets rock-hard and often needs a spray foam removal saw or an oscillating multi-tool to release it from timber. We use a thermal imaging camera to map where foam has failed and where roof timber rot has already started, then remove it without spreading dust through your home.
Most Telford enquiries come from three situations: a mortgage refusal due to spray foam, a surveyor flagging loft condensation, or rising energy bills after foam shrank away from the rafters. Older terraces around Dawley and Oakengates often have shallow roof voids where foam was sprayed directly onto felt, trapping damp against the timber. If you have been searching for local spray foam removal Telford Shropshire, we survey the loft, photograph every affected rafter and tell you honestly whether full removal is needed or whether a partial strip will satisfy your lender.
Why Telford homeowners book spray foam removal
Removing failed foam is rarely about the foam itself. It is about getting a mortgage approved, stopping rot in your roof timbers, and cutting the damp smell that creeps into back bedrooms.
Unblocks mortgage lending
Most high street lenders refuse to lend on a property with spray foam under the roof deck. We remove the foam, document the condition of every rafter with photographs, and issue a completion report your surveyor and lender can act on. Typical turnaround from survey to signed-off report is 5 to 10 working days.
Stops roof timber rot
Closed cell foam traps moisture against rafters and purlins, and rot follows within a few seasons. Our technicians cut foam back to clean timber, treat early surface rot, and leave the roof void ventilated. On a typical Telford semi-detached loft we remove 8 to 14 cubic metres of foam in a single day.
Cuts damp and condensation
Loft condensation shows up as black mould on roof felt, musty air in upstairs rooms and wet patches on chimney breasts. Once the foam is out and airflow is restored, most Telford properties dry out within two to three weeks. We fit vent trays and check existing loft insulation at the same time.
Restores insulation performance
Foam that has shrunk away from the rafters leaves cold bridges and pushes your heating bills up. We remove the failed material and reinstate loft insulation to current standards, so the roof space performs properly again. Most customers see the difference in the first full winter after the work.
How our spray foam removal process works
Every job follows the same five steps, from the first phone call to the final report. You get a fixed price after the survey, and you know what happens on each day of the work.
Survey and quote
We visit your Telford property, inspect the loft or cavity, and use a thermal imaging camera to find hidden damp and failed foam. You get a written fixed price within 24 hours, covering removal, disposal and the completion report. Surveys take 45 to 60 minutes.
Protect and prepare
On the day of the work we lay dust sheets, seal the loft hatch and set up an industrial vacuum with HEPA filtration. Our technicians wear respirators and protective clothing. Preparation usually takes 30 to 45 minutes before any cutting begins.
Cut and extract foam
We cut the foam into manageable sections using a spray foam removal saw and oscillating multi-tool, then lift it out by hand and bag it. For hard, brittle closed cell foam we switch to dry ice blasting, which freezes the foam so it releases from timber without gouging the wood.
Clean and inspect timber
Once the foam is out, we vacuum every rafter, purlin and felt surface, then inspect the timber for rot. Any early decay is treated and photographed. This stage typically takes two to four hours on a standard Telford loft.
Report and handover
We reinstate loft insulation where needed, ventilate the roof void, and hand you a completion report with before-and-after photographs. Most lenders accept this document alongside a surveyor's re-inspection. We also explain how to keep the loft dry going forward.
Four years removing spray foam across Shropshire
AeroSpace Spray Foam Team has been removing spray foam insulation since 2022, working on lofts, rafters, cavity walls and commercial roofs across Telford and Shropshire. Our technicians hold BPCA certification and CITB certification, and we work to CHAS, Constructionline and SafeContractor standards on every site. We have completed hundreds of removals on Telford's mixed housing stock, from 1930s semis in Wellington to modern timber-frame homes in Lightmoor. That experience matters when a lender wants documented evidence and when a roof void needs to be returned to a safe, ventilated condition.
- BPCA-certified technicians trained in safe foam removal and controlled waste disposal
- CHAS, Constructionline and SafeContractor accredited for domestic and commercial work
- CITB certification covering working at height and roof void safety
- Thermal imaging surveys to locate hidden damp before cutting begins
- Experience with BASF, Dow and Huntsman foam systems found in Telford lofts
Why choose our Spray Foam Removal near me in Telford
We are a local Telford team, not a national call centre. You speak to the people who will actually be in your loft, and you get a fixed price before we start.
Fixed price, no surprises
Every quote is fixed after the survey, covering removal, disposal, cleaning and your completion report. No day rates, no hidden extras for hard-to-reach rafters. If we find more foam than expected, we tell you before we continue and re-quote in writing.
Dust-controlled removal
We seal the loft hatch, run industrial vacuum extraction with HEPA filters, and bag all foam on site. Your landing, carpets and stairwell stay clean. On an average Telford job we remove between 40 and 90 bags of foam, all disposed of through licensed waste routes.
Mortgage-ready documentation
If you need spray foam removal company near me Telford for a lender, our completion report includes dated photographs of every rafter, notes on timber condition, and confirmation that the roof void is ventilated. Surveyors and lenders across Shropshire accept this format.
Local coverage, fast response
We cover Telford Town Centre, Wellington, Madeley, Dawley, Oakengates and the surrounding villages. Most surveys are booked within 48 hours of your call, and emergency spray foam removal near me Telford requests are prioritised where a sale is at risk.
What our spray foam removal service includes
Every Telford removal is quoted as a complete package, so you know exactly what is covered before we start. If your property needs something extra, such as cavity wall work or a full roof survey, we price it separately and in writing after the survey.
Full loft survey
We inspect the roof void, identify the foam type, and use a thermal imaging camera to find hidden damp, failed insulation and early timber rot. The survey takes 45 to 60 minutes and there is no charge.
Foam cutting and extraction
We cut out open cell, closed cell and mixed foam using a spray foam removal saw, oscillating multi-tool and, where needed, dry ice blasting. All foam is bagged on site and removed the same day.
Timber inspection and treatment
Every rafter and purlin is vacuumed and checked for rot. Early surface decay is treated and photographed. If structural timber needs replacing, we tell you before we finish and quote separately.
Ventilation and insulation reinstatement
We restore airflow through the roof void, fit vent trays where needed, and reinstate loft insulation to current standards. This is what stops the damp returning after the foam has gone.
Completion report for lenders
You receive a dated report with before-and-after photographs, timber condition notes and confirmation that the roof void is ventilated. Most Shropshire lenders and surveyors accept this format for mortgage purposes.
Licensed waste disposal
All removed foam is disposed of through licensed waste routes, with paperwork available on request. We recycle where the material allows and never fly-tip or mix foam with general building waste.
Problems our Telford spray foam removal solves
Failed spray foam rarely stays a small problem. It traps moisture, damages timber and blocks lending. Here are the issues we fix most often for Telford homeowners and landlords.
Mortgage refused because of spray foam
Your sale stalls, your buyer walks away, and you lose the chain. Most high street lenders will not lend on a property with foam under the roof deck until it is removed and documented.
We remove the foam, photograph every rafter, and issue a completion report your lender and surveyor can act on. Most Telford sales complete within six to eight weeks of the removal.
Loft condensation and black mould
Moisture trapped by foam condenses on cold felt, causing black mould, musty smells and damp patches on ceilings below. Left alone, it spreads into the roof timbers.
We cut out the foam, restore airflow through the roof void, and fit vent trays where needed. Most Telford lofts dry out within two to three weeks, and we check the insulation at the same time.
Roof timber rot around rafters
Closed cell foam holds water against timber, and rot follows within a few seasons. Early decay weakens rafters and purlins and can turn a simple removal into a structural repair.
Our technicians cut foam back to clean timber, treat early surface rot, and photograph the condition of every rafter. If structural repair is needed, we tell you before we finish and quote separately.
Rising energy bills after foam shrinkage
Foam that has shrunk away from the rafters leaves cold bridges and gaps, so heat escapes through the roof and your bills climb. The insulation you paid for is no longer doing its job.
We remove the failed foam and reinstate loft insulation to current standards, closing the cold bridges. Most Telford customers notice the difference in the first full winter after the work.
When Telford homeowners call us
A buyer's surveyor flags spray foam in the loft and the lender withholds the mortgage until it is removed.
We survey within 48 hours, give a fixed price, and remove the foam in a single day. The completion report goes to your lender with dated photographs of every rafter and confirmation that the roof void is ventilated.
The lender releases funds, the sale completes, and the new owner inherits a documented, mortgage-ready roof space.
A landlord in Dawley has two terraces with closed cell foam and tenants reporting damp smells in the back bedrooms.
We cut the foam out with a saw and multi-tool, treat early rot on the purlins, fit vent trays and reinstate loft insulation. Work is scheduled between tenancies to avoid disruption.
Both lofts dry out within three weeks, the damp smell clears, and the properties pass their next inspection without foam-related defects.
A homeowner in Wellington notices foam has shrunk away from the rafters and their winter heating bills have jumped.
We remove the failed foam, check the timber for rot, and reinstate loft insulation to current standards. A thermal imaging survey confirms where the cold bridges were.
The roof void performs properly again, and the customer sees lower winter bills and a warmer upstairs landing.
A commercial unit near Donnington has spray foam under a warehouse roof and the insurer wants evidence it has been dealt with.
We plan the work around shift patterns, use scissor lifts where needed, remove the foam and issue the documentation the insurer and landlord require.
The insurer signs off the building, and the site returns to normal operation with no lost production days.
Tools and methods we use
Tools & Equipment
Spray foam removal saw
Cuts thick closed cell foam into manageable sections without tearing the roof felt or gouging rafters. It is the first tool we reach for on most Telford lofts.
Oscillating multi-tool
Gets into tight corners around rafters, purlins and chimney breasts where a full saw will not fit. Ideal for Telford terraces with shallow roof voids.
Dry ice blasting machine
Freezes brittle closed cell foam so it releases from timber without damaging the surface. It leaves no blasting media behind and is safe around roof membranes.
Thermal imaging camera
Maps hidden damp, failed insulation and cold bridges before we cut anything. It shows exactly where foam has shrunk away from the rafters.
Industrial vacuum with HEPA filtration
Captures dust and foam particles at the source, keeping your landing and stairwell clean. We run it throughout the removal, not just at the end.
Respirator and protective clothing
Protects our technicians from isocyanate residues and airborne foam dust. We wear full PPE on every job, including surveys.
Scraper and chisel
Hand tools for lifting the last traces of foam from timber and brickwork after the saw and blasting work is done.
Methods
Dry ice blasting
We use dry ice pellets to freeze closed cell foam so it releases cleanly from rafters and felt. It is faster than cutting on brittle foam and avoids gouging the timber. No blasting media is left behind, so the roof void is ready for inspection immediately.
Sand blasting media
For stubborn foam residues on brick, stone and concrete, we use controlled sand blasting media to strip the last traces. It prepares the substrate for new insulation or render and is used only where the surface can take it.
Thermal imaging survey
Every Telford job starts with a thermal imaging camera survey. We map damp, cold bridges and failed foam before cutting, so the removal targets the right areas and the report shows the lender exactly what was found.
Controlled waste disposal
All foam is bagged, labelled and removed through licensed waste routes. We keep disposal paperwork and recycle where the material allows, so your property and our records are both clean.
How spray foam removal runs in Telford
Telford sits in Shropshire with a mix of 1930s semis, post-war terraces and modern timber-frame estates, and each type behaves differently when foam is involved. Older properties around Dawley, Oakengates and Madeley often have shallow roof voids where foam was sprayed straight onto felt, trapping damp against rafters through the winter. Newer homes in Lightmoor and Shawbirch tend to have deeper voids and better ventilation, so removal is usually quicker. Shropshire's damp, mild climate means loft condensation is a year-round risk rather than a winter-only problem, and we see the worst cases after a wet autumn. If you have been searching for affordable spray foam removal near me Telford Shropshire, we survey the loft, confirm the foam type, and give you a fixed price that covers removal, disposal, ventilation and your completion report. We also work with local surveyors who understand the documentation lenders ask for.
Service Areas
A high proportion of 1930s semis with shallow roof voids and foam sprayed onto felt. Removal usually takes one day, with vent trays fitted to restore airflow.
Terraced housing with chimney breasts that trap damp once foam is applied. We treat early rot on purlins and check the chimney flashing while we are in the loft.
Modern timber-frame homes with deeper roof voids. Foam removal is quicker here, but we still run a thermal imaging survey to confirm no cold bridges remain.
Mixed residential and commercial stock. We schedule warehouse and workshop removals around shift patterns to avoid disrupting operations.
Local Considerations
Damp Shropshire winters
Mild, wet weather keeps roof voids humid for months. Foam traps that moisture against timber, so we prioritise ventilation and check for rot on every job.
Shallow roof voids in older terraces
Access is tight around Dawley and Oakengates, so we use compact cutting tools and hand extraction rather than large equipment.
Mixed foam types in one loft
Some Telford lofts have open cell foam near the eaves and closed cell foam between rafters. We match the removal method to each area rather than using one approach throughout.
Mortgage-driven deadlines
When a lender is waiting, we prioritise the survey and removal, and issue the completion report within 48 hours of finishing on site.
Mortgage refusal to completion in Wellington
A 1930s semi in Wellington had closed cell foam sprayed across every rafter. The buyer's lender refused to lend, the sale stalled, and the seller was facing a second lost chain. The loft smelled damp and the felt was black with mould.
We removed 11 cubic metres of foam in one day, treated early rot on two purlins, and fitted vent trays. The completion report went to the lender within 48 hours, and the sale completed six weeks later.
Maintenance & Follow-up
Check the loft each autumn for new damp patches and keep the vent trays clear. We recommend a thermal imaging check every three years.
Two terraced houses in Dawley had closed cell foam around the chimney breasts and damp patches on the back bedroom ceilings. Tenants had complained for two winters, and the landlord was losing rent between tenancies.
We cut the foam out with a saw and multi-tool, treated surface rot on the purlins, and reinstated loft insulation. Both lofts dried out within three weeks and the damp smell cleared completely.
Maintenance & Follow-up
Keep the loft hatch closed but not sealed, and check the chimney flashing each spring. New insulation should be inspected once a year.
A modern home in Lightmoor had open cell foam that had shrunk away from the rafters, leaving visible gaps and cold bridges. Winter heating bills had climbed noticeably over two seasons.
We removed the failed foam, vacuumed the roof void, and reinstated loft insulation to current standards. A thermal imaging survey confirmed the cold bridges were closed, and the customer reported lower bills the following winter.
Maintenance & Follow-up
Check the loft insulation depth every couple of years and top up if it settles. Keep an eye on the eaves for any new draughts.
How do I find spray foam removal near me in Telford?
Call us on 0195 230 1076 or book a survey online, and we will be at your Telford property within 48 hours. We inspect the loft, confirm the foam type, and give you a fixed price within 24 hours of the visit. There is no charge for the survey, and you are under no obligation to book the removal.
Is there a local spray foam removal company near me in Telford?
Yes. AeroSpace Spray Foam Team is based in Telford and has been removing spray foam insulation across Shropshire since 2022. We cover Telford Town Centre, Wellington, Madeley, Dawley, Oakengates, Donnington and the surrounding villages. You deal directly with our own technicians, not a subcontractor or a national call centre.
How quickly can you get to my Telford property for spray foam removal?
Most Telford surveys are booked within 48 hours, and full removals usually start within 5 to 10 working days. If your mortgage offer is at risk we prioritise the job and can often begin within 3 working days. A standard loft removal takes one day on site, with the completion report issued within 48 hours.
Do you cover all Telford Shropshire areas for spray foam removal near me?
We cover the whole of Telford and surrounding Shropshire, including Wellington, Madeley, Dawley, Oakengates, Stirchley, Donnington, Hadley, Leegomery, Muxton, Shawbirch, Ketley, Malinslee, Woodside, Brookside, Aqueduct, Hollinswood, Randlay, Sutton Hill and Lightmoor. If you are just outside these areas, call us and we will confirm coverage before booking.
Accredited, certified and local
Certifications
Reviews
Surveyed our loft in Wellington within two days and removed the foam in one visit. The report with photos of every rafter satisfied our lender and the sale went through. Tidy work and no mess left behind.
Two terraces in Dawley with closed cell foam and damp patches. They cut it out, treated the purlins and fitted vent trays. Both lofts are dry and the tenants have stopped complaining.
Open cell foam had crumbled around our rafters and the bills kept rising. The team vacuumed everything, checked the timber and reinstated the insulation. Explained what to check each spring.
Commercial unit near Donnington needed foam removed for our insurer. Worked around our shifts, used scissor lifts and issued the paperwork we needed. No lost production days.
Related Services
same day Spray Foam Removal
When a lender or buyer needs foam gone fast, we can mobilise a same day Spray Foam Removal crew across Telford. We carry cutting tools, extraction equipment and disposal bags on the van, so a standard loft strip can begin the day you call.
same day Spray Foam Removal24/7 Spray Foam Removal
Our 24/7 Spray Foam Removal line handles urgent calls from Telford homeowners, landlords and agents. If a sale is about to collapse or water is tracking through a foam-filled roof void, call 0195 230 1076 and we will arrange the earliest possible attendance.
24/7 Spray Foam RemovalResidential Spray Foam Removal
Most of our Telford work is residential: lofts, rafters and cavity walls in semis, terraces and detached homes. We protect your carpets and stairwell, work around family routines, and leave the property clean enough to sleep in the same night.
Residential Spray Foam RemovalCommercial Spray Foam Removal
We remove spray foam from warehouses, workshops and commercial roofs across Telford and Shropshire. Work is planned around your operating hours, with method statements, risk assessments and SafeContractor accreditation in place before we start.
Commercial Spray Foam Removalloft spray foam removal
Loft spray foam removal is our most requested service in Telford. We cut foam from rafters, purlins and roof felt, clear the debris, check for rot and restore ventilation. A typical Telford loft takes one day, with the completion report following within 48 hours.
loft spray foam removalroof spray foam removal
Foam sprayed directly onto the underside of roof tiles or felt traps moisture and accelerates decay. Our roof spray foam removal service in Telford releases the foam without damaging tiles or membrane, then reinstates airflow so the roof structure can dry out properly.
roof spray foam removalAttic spray foam removal
Attic spray foam removal in Telford covers older properties where foam was applied between rafters and around chimney breasts. We work in tight spaces using compact cutting tools and industrial vacuum extraction, leaving the attic clean, dry and ready for inspection.
Attic spray foam removalspray foam insulation removal
Our spray foam insulation removal service handles open cell, closed cell and mixed foam systems. We identify the product, choose the right removal method, and dispose of everything through licensed waste routes. Most Telford jobs are completed in a single day.
spray foam insulation removalopen cell spray foam removal
Open cell foam crumbles and holds moisture against timber. We remove it by hand and with vacuum extraction, then treat any early rot. Telford properties with open cell foam often need new loft insulation once the old material is out.
open cell spray foam removalclosed cell spray foam removal
Closed cell foam sets hard and bonds tightly to rafters. We use a spray foam removal saw, oscillating multi-tool and, where needed, dry ice blasting to release it cleanly. This is the most common foam type we find in Telford lofts.
closed cell spray foam removalmortgage lender spray foam removal
If your lender has refused a mortgage because of spray foam, we provide the removal and the documentation they need. Our Telford reports include dated photographs, timber condition notes and confirmation that the roof void is ventilated and mortgage-ready.
mortgage lender spray foam removalinsulation removal service
Beyond spray foam, our insulation removal service covers contaminated mineral wool, damaged boards and failed loft insulation. We clear the roof space, dispose of the old material responsibly and prepare the area for new insulation to current standards.
insulation removal serviceinsulation assessment
Our insulation assessment uses thermal imaging to show where foam has failed, where damp is trapped and where heat is escaping. Telford homeowners use this survey to decide between partial removal, full removal or a ventilation-led repair.
insulation assessmentdry ice blasting spray foam removal
Dry ice blasting freezes foam so it releases from timber without gouging the surface. We use it on brittle closed cell foam and on rafters where a saw would cause damage. It is clean, fast and leaves no blasting media behind.
dry ice blasting spray foam removalCavity wall spray foam removal
Cavity wall spray foam removal in Telford addresses damp bridging and failed insulation in the wall cavity. We inspect with a thermal imaging camera, remove the foam through controlled access points, and restore the cavity so it can drain and ventilate correctly.
Cavity wall spray foam removalsand blasting spray foam insulation removal
For stubborn foam residues on brick, stone and concrete, we use sand blasting spray foam insulation removal with controlled media. It strips the last traces of foam from awkward surfaces, leaving a clean substrate ready for new insulation or render.
sand blasting spray foam insulation removalthermal spray foam removal
Thermal spray foam removal uses heat-controlled cutting tools to soften foam before extraction. It suits thick closed cell layers where a saw would be slow or risky. We match the method to the foam on your Telford property after the survey.
thermal spray foam removalenvironmentally friendly insulation removal
We bag, label and dispose of all foam through licensed waste routes, and we recycle where the material allows. Our environmentally friendly insulation removal approach keeps foam out of landfill wherever possible and leaves your Telford property clean and safe.
environmentally friendly insulation removalWarehouse spray Foam removal
Warehouse spray Foam removal across Telford and Shropshire is planned around your shifts. We work in bays and roof voids with scissor lifts where needed, remove the foam, and issue the documentation your insurer or landlord requires.
Warehouse spray Foam removalBook Spray Foam Removal near me in Telford today
Call 0195 230 1076 and we will book your survey within 48 hours. Fixed prices, dust-controlled removal and a completion report your lender can act on. BPCA-certified, CHAS accredited, and local to Telford since 2022.